Skip to main content

Sniffing the Buderus Logamatic 4000 bus

Avid readers of this blog might know that I already had a couple of projects around the heating in our house. The latest addition to these projects is a mechanism to listen in on the Buderus's bus to gather and log information such as outside temperature, target temperatures in the heating circuits, turn-on and turn-off temperatures of the burner, etc.

My intention with this information is to improve heating efficiency (as measured in gas used) and also to get a more in-depth understanding of the engineering aspects of this system (mechanical & electronic engineering and computer science).

Previously I've installed DS18B20 sensors all around, monitoring the system from the "outside", by sniffing the bus, I get a peek into the inside of the system.

When I started, I've found the site https://www.holzleitner.com/el/buderus-monitor/index-en.html which contained a reverse-engineered description of how the bus system of Buderus works.

Then I've stumbled into the  BBQKees webshop which sells complete boards to connect a Raspberry Pi to the boiler, from which I quickly purchased one.

Unfortunately the BBQKees board turned out to be incompatible with my boiler, but I've learnt a lot from trying to make it work:

  • had to le-learn electronics basics, voltage dividers, capacitors, etc
  • the use of an oscilloscope, even outside of my lab (e.g. connected to the boiler and various points on the board)
  • the electrical encoding of an RS232 signal

I couldn't make the BBQKees board work, which is a but of a let-down but I truly enjoyed the process. The details have been documented on this twitter thread.

With that failure, I decided to solder my own board, as described on the Holzleitner site. And with that I was successful.

My RPi is now receiving the 1200 8N1 signal that the boiler is sending out to the room unit, which I can now use to chart changes in boiler behavior in Homeassistant.

 

The chart shows a combination of data acquired via DS18B20 sensors and the data acquired via the bus sniffer:

  • the red chart shows the temperature of the hot water produced by the boiler (DS18B20),
  • the green one is the internal temperature of the boiler (reported by the boiler)
  • the two straight lines show the turn-on and turn-off temperature of the burners (also from the bus)
  • And the history chart on the top shows wether the burner is active or not.

This is just the beginning. I intend to attach a sensor to our gas meter, so I can relate the burning time with the amount of gas used. But I also have plans to change how the system controls pumps, as I am pretty convinced that the way it works right is not ideal. I am going to monitor this data, in order to get a baseline and to confirm my hypothesis.

36550006300672?ref_src=twsrc%5Etfw%7Ctwcamp%5Etweetembed%7Ctwterm%5E1354836550006300672%7Ctwgr%5E%7Ctwcon%5Es1_c10&ref_url=https%3A%2F%2Fpublish.twitter.com%2F%3Fquery%3Dhttps3A2F2Ftwitter.com2FBazsi7712Fstatus2F1354836550006300672widget%3DTwe

Labels:

Comments

Jieffe said…
Great job ! I've grabbed the popcorn and am waiting for the next episode :)

I've got a Buderus boiler too and I'd like to retrieve data from it.
6:34 PM
Post a Comment

Popular posts from this blog

syslog-ng fun with performance

I like christmas for a number of reasons: in addition to the traditional "meet and have fun with your family", eat lots of delicious food and so on, I like it because this is the season of the year when I have some time to do whatever I feel like. This year I felt like doing some syslog-ng performance analysis. After reading Ulrich Deppert's series about stuff "What every programmer should know about memory" on LWN, I thought I'm more than prepared to improve syslog-ng performance. Before going any further, I'd recommend this reading to any programmer, it's a bit long but every second reading it is worth it. As you need to measure performance in order to improve it, I wrote a tool called "loggen". This program generates messages messages at a user-specifyable rate. Apart from the git repository you can get this tool from the latest syslog-ng snapshots. Loggen supports TCP, UDP and UNIX domain sockets, so really almost everything can be me
17 comments
Read more

syslog-ng roadmap 2.1 & 2.2

We had a meeting on the syslog-ng roadmap today where we decided some important things, and I thought I'd use this channel to tell you about it. The Open Source Edition will see a 2.1 release incorporating all core changes currently in the Premium Edition and additionally the SQL destination driver. We are going to start development on the 2.2 PE features, but some of those will also be incorporated in the open source version: support for the latest work of IETF syslog protocols unique sequence numbering for messages support for parsing message contents Previously syslog-ng followed the odd/even version numbering to denote development/stable releases. I'm going to abandon this numbering now: the next syslog-ng OSE release is going to have a 2.1 version number and will basically come out with tested code changes only. The current feature set in PE were developed in a closed manner and I don't want to repeat this mistake. The features that were decided to be part of the Open
12 comments
Read more

syslog-ng 3.0 and SNMP traps

Last time I've written about how syslog-ng is able to change message contents. I thought it'd be useful to give you a more practical example, instead of a generic description. It is quite common to convert SNMP traps to syslog messages. The easiest implementation is to run snmptrapd and have it create a log message based on the trap. There's a small issue though: snmptrapd uses the UNIX syslog() API, and as such it is not able to propagate the originating host of the SNMP trap to the hostname portion of the syslog message. This means that all traps are logged as messages coming from the host running snmptrapd, and the hostname information is part of the message payload. Of course it'd be much easier to process syslog messages, if this were not the case. A solution would be to patch snmptrapd to send complete syslog frames, but that would require changing snmptrapd source. The alternative is to use the new parse and rewrite features of syslog-ng 3.0. First, you need to f
2 comments
Read more